The 7707CVTA15 is a VistaLINK® capable, composite analog video and analog audio fiber transmitter for broadcast quality video and analog audio signals. This single card module accepts one NTSC or PAL analog video input with up to four analog audio inputs, performs analog to digital conversion and transmits them over a single fiber. The companion 7707CVRA Composive Video and Analog Audio Fiber Receiver demultiplexes the signals and converts them back to analog form.
Single card fiber multiplexor for one or two analog video and four analog audio signals
Supports both NTSC and PAL
Broadcast quality analog video and audio performance
Meets or exceeds EIA/TIA RS250-C short haul specifications for analog video and audio transport
Superior digital data transmission
Video loop-through for additional signal distribution or monitoring (7707CVTA only)
Signal transport over fiber uninterrupted by loss of input video or audio feeds
Low Audio to Video latency
Comprehensive Signal and card status monitoring via four-digit card-edge display, or remotely through SNMP and VistaLINK® capability
VistaLINK® capable for remote monitoring via SNMP (using VistaLINK® PRO) when installed in 7800FR frame with a 7700FC VistaLINK® Frame Controller
Adjustable gain equalization for up to 250m of Belden 1694 coaxial cable
Fully hot-swappable from front of frame with no fiber disconnect/reconnect required
Supports single mode and multi-mode fiber optic cable
Optical output wavelengths at 1310nm, 1550nm, and up to sixteen CWDM wavelengths (ITU-T G.694.2 compliant)
DWDM wavelengths (ITU-T G.694.1 compliant) also available
Fiber Optic Connector Type - Other
Fiber Optic Signals Supported - Other
Spec Sheet available - Yes
DC Voltage:
12 Volts
Regulatory Compliance:
Class 1 laser product, 24CFR 1040.10 and 1040.11, IEC 60825-1, FCC Part 15, Class A, EU EMC Directive (EMI/RFI)
Active Power:
11/12 Watt
Analog Video Input Standard:
NTSC, SMPTE ST 170, PAL ITU-R624-4
Analog Video Input Number of Inputs 7707CVTA:
1
Analog Video Input Number of Inputs 7707CVTA-2:
2
Analog Video Input Connector:
BNC per IEC 61169-8 Annex A
Analog Video Input Signal Quantization:
12 bits
Analog Video Input System Bandwidth:
5.5 MHz
Analog Video Input Level:
2 V p-p (maximum)
Analog Video Input Gain Equalization:
Up to 250m of Belden 1694 or equivalent (adjustable)
Analog Video Input Impedance:
75 ohm
Analog Video Input Return Loss:
> 30dB to 5.5 MHz
Analog Video Input SNR:
> 70 dB
Analog Video Input Differential Gain:
< 1.0%
Analog Video Input Differential Phase:
< 0.7°
Analog Video Input Passband Ripple:
Analog Video Input NTSC:
< ±0.1dB to 4.1 MHz
Analog Video Input:
< ±0.2dB to 5.5 MHz
Analog Video Input PAL:
< ±0.1dB to 4.8 MHz
Analog Video Input Chroma/Luma Gain:
98% - 103 %
Analog Video Input Chroma/Luma Delay:
Analog Video Input NTSC:
< 5ns
Analog Video Input PAL:
< 12ns
Analog Video Input Line Time Distortion:
1.2 %
Analog Video Output 7707CVTA Only:
Analog Video Output Standard:
NTSC, SMPTE ST 170, PAL ITU-R624-4
Analog Video Output Number of Outputs:
1 buffered version of input
Analog Video Output Connector:
BNC per IEC 61169-8 Annex A
Analog Video Output Level:
1 V p-p
Analog Video Output Impedance:
75 ohm
Analog Video Output Return Loss:
> 30dB to 5.5 MHz
Analog Audio Input Number of Inputs:
4
Analog Audio Input Type:
Balanced analog audio
Analog Audio Input Connector:
12 pin removable terminal block
Analog Audio Input Impedance:
High Impedance (> 20kohm)
Analog Audio Input Frequency Response:
±0.1dB (20Hz to 20KHz)
Analog Audio Input THD:
< 0.005% (20Hz to 20kHz)
Analog Audio Input Channel Phase Differential:
< ±1°
